![]() ![]() If they are spinning, you could just be stuck or have a flat tire. If your riding mower won’t move forward or reverse, check to see what the wheels are doing. A Few Worthy Mentions When Your Riding Mower Won’t Move Forward or Reverse Once the lever is in the correct position, the hydrostatic drive will be reengaged and ready to drive. Once you have located the disengage lever, you must check its location. You can check it’s correctly installed by putting the mower back in drive and ensuring the wheel has firm contact with the friction plate. If you need to cut it to length, cut it so that it’s a snug fit and the ends touch.įinally, take the lawn mower out of drive and reinstall the friction wheel onto the bolts. If you have to install the lining yourself, ensure that both ends of the lining are touching when you place it inside the wheel. Sometimes these can be shipped without the internal lining installed or in the wrong length. Grab your replacement wheel and check that there is an internal plastic lining. ![]() You will find this helps stop the wheel from turning. If your wheel spins while removing the nuts, you may want to try using a second wrench on a second nut simultaneously. To remove a friction wheel, you’ll first need to remove the mounting nuts using your wrench. All that remains is to reattach the clutch power and clutch locator bracket. Once completed, you will have a new drive belt installed. Be careful with your fingers when handling the spring. Then, take your spring puller and reinstall the tension spring. Next, move the tensioner into place, which will help hold the belt in position. Now grab your new belt and place it over the pulleys. With the tension out of the drive belt, you’ll be able to remove it. Pull the spring off the tensioner and put it to one side. Alternatively, you can use a big set of pliers or grips. It makes light work and keeps your fingers in the clear. The best way to remove a large spring is with a spring puller. If not, then you’ll need to remove the tensioner spring. If the drive belt is loose, then you may be able to lift it over the pulleys. Disconnect the connector and tuck it out of the way. The final obstruction is the clutch power connector. You’ll need to locate the clutch alignment bracket and use a socket wrench to remove the bolts. Then lower the deck as low as it will go. Start by applying the brakes and disconnecting the battery. If you discover that the belt is slack, you must replace it. ![]() Now that you have found why your riding mower won’t go forward or reverse, let’s dig into what you’ll need to get it moving again. How to Fix a Riding Mower that Won’t Go Forward or Reverse If you can spin the friction wheel freely, you know it has worn down and needs replacement. With the lawn mower in drive, the friction wheel and the friction plate should be in firm contact with one another. Checking the Friction Wheel is in Contact with the Friction Plate So, look at the lawn mower’s rear or under the seat, locate the disengage lever, and ensure it’s engaged. But, if this happens and isn’t reengaged, it will not work when you want to use the lawn mower. Unknown to some, you can disengage the drive system of a hydrostatic drive. ![]() Checking The Hydrostatic Drive is Engaged The most common issue is that the belt has worn out and has stretched. Therefore, inspect these 3 parts to ensure they function correctly and aren’t damaged. It could be a problem with the belt itself, the pulleys, or the idler. If you find you have a slack belt, you’ll need to know the cause. The belt should be nice and tight not too tight but definitely not baggy. With the drive engaged, you can jump off the lawn mower and look at the belt. Then, if you have a drive system with an idler, place the mower in drive. Inspecting the Drive Beltįirst, switch off the lawn mower and apply the brake. These are all common causes of this issue. Here I’ll cover how you can diagnose the drive system’s belt, a potentially disengaged hydrostatic drive, and what could be a worn-down friction plate. 3 Reasons for a Riding Mower that Won’t Move Forward or Reverse You’ll probably find a problem in the belt, hydrostatic, or friction plate drives. The drive system is the first place to inspect when your mower won’t move forward or reverse. 4 A Few Worthy Mentions When Your Riding Mower Won’t Move Forward or Reverse Why Won’t My Riding Mower Go Forward or Reverse? (The Short Answer) ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |